Nowy Matek H743-WING V2 ArduPilot INAV 3-8S MPU6000 oraz ICM42605 w Chełm

Fabrycznie nowy, rozpakowany tylko do zdjęć. Sprzedaję bo rezygnuję z parapetów na rzecz kopterów.
Jest to lepsza wersja z dobrym i sprawdzonym IMU: MPU6000 (SPI1) & ICM42605 (SPI4), a nie ICM42688P
Chcesz przesyłkę OLX pisz do mnie.
Poniżej specyfikacja producenta:

FC Specifications

MCU: STM32H743VIT6, 480MHz , 1MB RAM, 2MB Flash
IMU: MPU6000 (SPI1) & ICM42605 (SPI4)
Baro: Infineon DPS310 (I2C2)
OSD: AT7456E (SPI2)
Blackbox: MicroSD card slot (SDIO)
7x Uarts (1,2,3,4,6,7,8) with built-in inversion.
13x PWM outputs(including “LED” pad)
2x I2C
1x CAN
6x ADC (VBAT, Current, RSSI, Analog AirSpeed, VB2, CU2)
3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
1x SPI3 breakout
USB/Beep Extender with Type-C(USB2.0)
Dual Camera Inputs switch
5V/9V(12V) for Camera/VTX power switch
High-precision Current Sense (90A continuous, 220A peak)
Battery Voltage Sensor: 1K:10K (Scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)
ADC VB2 voltage divider: 1K:20K
ADC AirSpeed voltage divider: 20K:20K
Static power 160mA-5V
FC Firmware

ArduPilot(ChiBiOS): MATEKH743
INAV: MATEKH743
PDB

Input voltage range: 8~36V (3~8S LiPo) w/TVS protection
2x ESC power pads
Current Senor: 220A, 3.3V ADC (Scale 150 in INAV, 66.7 A/V in ArduPilot)
Sense resistor: 90A continuous, 220A peak.
BEC 5V output

Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed
Output 5.15 /- 0.1V DC
Continuous current 2 Amps, 3A Peak
BEC 9V /12V output

Designed for Video Transmitter, Camera, Gimbal ect.
Continuous current 2 Amps, 3A Peak
12V option with Jumper pad
BEC Vx output

Designed for Servos
Voltage adjustable, 5V Default, 6V or 7.2V via jumper
Continuous current 8 Amps, 10A Peak
BEC 3.3V output

Linear Regulator
Continuous current: 200mA
Physical

Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
Dimensions: 54 x 36 x 13 mm
Weight: 30g with USB extender
Including

1x H743-WING
1x USB(Type-C)/Beep (Passive buzzer) Extender
1x 20cm JST-SH-6P to JST-SH-6P cable for USB extender.
2x 20cm JST-GH-4P to JST-GH-4P cable for CAN & I2C port
1x Rubycon ZLH 35V 470uF capacitor
Dupont 2.54 pins (Board is shipped unsoldered)